Place of Origin:
CHINA
Brand Name:
GBS
Certification:
CE, UL, IEC, TUV,PONY,MA,ISO9001, ISO14001, OHSAS18001
Model Number:
GBS-LFP40Ah
Contact Us
rechargable lithium battery 40Ah GBS-LFP40Ah for electric motorcycle, mining backup power etc; LiFePO4 battery
|
Item |
Specification |
Remark |
||
|
Rated capacity |
40Ah |
0.2C rate discharge capacity |
||
|
Minimum capacity |
40Ah |
|||
|
Internal impedance |
≤0.8mΩ |
|
||
|
Nominal voltage |
3.2V |
|
||
|
Cell weight |
1.4±0.1KG |
|
||
|
Standard discharge conditions |
Constant current |
20A |
|
|
|
End-of-discharge voltage |
2.5V |
|
||
|
Standard charge method |
Constant current |
10A |
|
|
|
Charge voltage |
3.55V |
|
||
|
Fast charge method |
Constant current |
40A |
|
|
|
Charge voltage |
3.55V |
|
||
|
Max continuous discharge current |
120A |
|
||
|
Cycle life |
3000 cycles |
80% DOD |
||
|
Operating temperature |
Charging ambient temperature |
0~65°C |
|
|
|
Discharging ambient temperature |
-20~65°C |
|
||
|
Storage temperature |
-20~65°C |
|
||
|
Appearance |
Without break, distortion, contamination, leakage. |
|
||
Basic Performance
(1) High-efficiency output: standard discharge current 0.3-0.8C, instantaneous pulse discharge current 10C, lasting 10 seconds.
(2) Good high temperature performance, can work at 65℃. Temperature battery structure is safe and good.
(3) Good temperature at low pressure. The emission capacity is reduced to more than 78% at 0°C, and the discharge capacity is reduced to more than 70% at -20°C.
(4) Good safety PE performance: When the internal pressure of the battery is too high, the one-way safety valve will release gas and heat to ensure good battery performance. When the pressure inside the battery reaches a certain level, the valve opens immediately to protect the battery from burning and explosion.
(5) Long cycle life, single battery discharge capacity is still above 80% after 3000 cycles (80%DOD).
(6) It can be charged quickly. It can be charged to 80% in 20 minutes with 2-3h full charge.
(7) Low cost.
(8) No pollution in the manufacturing and use process.
Matters needing attention
(1) Please check if spare parts are completed when open the package and read the operation manual carefully.
(2) Do not make the battery Short Circuit,do not over charge and discharge.
(3) Please charge the new battery to full capacity before discharge for the first use.
(4) The battery pack is fixed with plate and strip before delivery, do not disassemble the plate and strip when using the battery.
(5) Checking the voltage of battery, normally it is 3.2V-3.3V.
(6) Fix BMS for battery pack and protect single cell to avoid over charge and over-discharge.
(7) Rivet or screw is used for battery connector.
(8) Please use copper part to connect battery packs and fix with hydraulic pressure plier. We could also provide the relevantconnection which fixed with screws.
(9) The charger used should be approved by our company in order to match with our lithium batteries.
(10) It will shorten battery cycle lifetime and damage battery due to overcharge and over-discharge if not do according to the above . It won’t be within our company warranty.
Requirement for safety assurance
For the sake of safety assurance, please discuss the equipment design, its system and protection circuit of Lithium-ion cell advance. And consult about the high rate current, rapid charge and special application in the same way.
Service line: +86-400-884-7799
Send your inquiry directly to us
